东莞市荣誉电子有限公司
五金通钻石会员 第14年
已通过企业工商认证
公司服务热线
15919886094
Electrical Requirements:
1 | Capacitance Tolerance 容量偏差 | ±20% at 120Hz,20℃ | ||||||||||||||||||||||||||||||||||||||
2 | Operation Temperature Range 工作温度 | 6.3V~100V -40℃~+105℃ | 160V~400V -25℃~+105℃ | |||||||||||||||||||||||||||||||||||||
3 | Rated Working Voltage And Surge Voltage 额定电压与 浪涌电压 | |||||||||||||||||||||||||||||||||||||||
W.V. | 6.3 | 10 | 16 | 25 | 35 | 50 | 63 | 100 | 160 | 200 | 250 | 350 | 400 | |||||||||||||||||||||||||||
S.V. | 7.3 | 11.5 | 18.4 | 29 | 40 | 58 | 73 | 115 | 184 | 230 | 287 | 400 | 460 | |||||||||||||||||||||||||||
4 | Leakage Current 漏电流 | After DC Voltage is applied to capacitor through the series protective resistance(1KΩ),and then terminal voltage may reach the rated working voltage. The leakage current when measured after 2 minutes (6.3-400V)shall be below the value of the following equation. 串联(1KΩ)保护电阻后，对产品施加额定直流工作电压(6.3~400V)两分钟后，漏电流值不大于下列规定值。 | ||||||||||||||||||||||||||||||||||||||
6.3~100V I≤0.01CV or 3μA(取较大值) Whichever is greater | 160~400V I≤0.03CV +10(μA) | |||||||||||||||||||||||||||||||||||||||
Where I=Leakage Current(μA) C=Capacitance(μF) V=Rated DC Working Voltage(V) | ||||||||||||||||||||||||||||||||||||||||
5 | Dissipation Factor 损耗角正切值 (at 120Hz,20℃) | |||||||||||||||||||||||||||||||||||||||
Rated Voltage | 6.3 | 10 | 16 | 25 | 35 | 50 | 63 | 100 | 160 | 200 | 250 | 300 | 400 | 450 | ||||||||||||||||||||||||||
Tanδ(max) | 0.24 | 0.20 | 0.16 | 0.14 | 0.12 | 0.10 | 0.09 | 0.08 | 0.12 | 0.12 | 0.15 | 0.15 | 0.23 | 0.23 | ||||||||||||||||||||||||||
标称容量大于1000μF时，每增加1000μF，损耗角正切值增加0.02。 | ||||||||||||||||||||||||||||||||||||||||
Endurance characteristic特性检测:
No | Item测试项目 | Conditions测试条件 | Specification特性要求 | |||||
1 | Rotational Temperature Test 温度快速变化 | Capacitor is place in an oven whose temperatures follow specific regulation to change. The specific regulation is “+20℃(3 min)→-40℃(30 min)→+20℃(3 min)→+105℃(30 min)→+20℃(3 min)”,and it is called a cycle. The test totals 5 cycles. And then the capacitor shall be subjected to standard atmospheric Conditions for 16 hours, after which measurement shall be made. 电容器在规定的温度范围内循环如下：“+20℃(3 min)→-40℃(30 min)→ +20℃(3 min)→+105℃(30 min)→+20℃(3 min)”，以上循环运行5次后,将电容器放置于标准气候中恢复16小时测量其值满足特性要求。 | Physical外观 | No broken and undamaged 无可见损伤及泄漏 | ||||
2 | High Temperature Load Life Test 耐久性 | Capacitors shall be placed in oven with application of ripple current and rated voltage for 1000hrs at 105℃. 在 105℃条件下，对电容器施加带有额定纹波电流的额定工作电压1000小时后，在标准气候下恢复16小时测量。 | Capacitance Change 容量变化 | Within±20% of the initial value 初始值的±20%以内 | ||||
TANδ 损耗角正切 | Less than 200% of specified value 不大于规定值的200% | |||||||
Leakage Current 漏电流 | Within specified value 不大于规定值 | |||||||
Physical外观 | No broken and undamaged 无可见损伤及泄漏 | |||||||
3 | High Temperature Unload Life Test 高温储存特性 | After 500 hrs test at 105℃ without rated working voltage. And then the capacitor shall be subjected to standard atmospheric conditions for 16 hours, after which measurements shall be made. 将电容器无负载放置于105℃条件，500小时后取出，放置于标准气候下恢复16小时测量. | Capacitance Change 容量变化 | Within±20% of the initial value 初始值的±20%以内 | ||||
TANδ 损耗角正切 | Lessthan200% of specified value 不大于规定值的200% | |||||||
Leakage Current 漏电流 | Less than 200% of specified value 不大于规定值的200% | |||||||
Physical外观 | No broken and undamaged 无可见损伤及泄漏 | |||||||
4 | Humidity Test 稳态湿热 | Capacitors shall be exposed for 500±6 hrs in an atmosphere of 90~95% R.H. at 40℃. And then the capacitor shall be subjected to standard atmospheric conditions for 16 hours, after which measurements shall be made. 电容器放置于湿度90~95% R.H.，温度40℃的大气中500±6小时.取出后在标准气候下恢复16小时测量. | Capacitance Change 容量变化 | Within±10% of the initial value 初始值的±10%以内 | ||||
TANδ 损耗角正切 | Lessthan200% of specified value 不大于规定值的200% | |||||||
Leakage Current 漏电流 | Within specified value 不大于规定值 | |||||||
Physical外观 | No broken and undamaged 无可见损伤及泄漏 | |||||||
5 | Vibration Test 振动测试 | 1.Fix it at the point 4mm or less form body. For ones of 12.5mm or more in diameter or 25mm or more length, use separate fixture. 2.Direction and during of vibration: 3 orthogonal directions Mutually each for 2hrs total 6hrs. 3.Frequency:10to 55Hz reciprocation for1 min. 4. Total amplitude: 0.75mm. 1.安装点距产品4mm以上。 2.在三个互相垂直轴的每一方向各振动2小时，共6小时。 3.频率:10到55Hz 每分钟互换。 4.振幅: 0.75mm. | Capacitance Change 容量变化 | Within±10% of the initial value 初始值的±10%以内 | ||||
TANδ 损耗角正切 | Within specified value 不大于规定值 | |||||||
Leakage Current 漏电流 | Within specified value 不大于规定值 | |||||||
Physical外观 | No broken and undamaged 无可见损伤及泄漏 | |||||||
6 | Solder Heat-Resistance Test 耐焊接热 | The section of lead below 4mm form the body of capacitor must be immersed in 260℃±5℃ liquid tin 10±1 seconds. Then. after removing the following specifications shall be satisfied when capacitor terminal is restored to 20℃ within two hours or over an hour. 距电容器本体4mm以下浸入 260℃±5℃ 的液体中10±1 秒. 取出后放入标准气候下恢复1~2小时测量。 | Capacitance Change 容量变化 | Within±5% of the initial value 初始值的±5%以内 | ||||
Physical外观 | No broken and undamaged 无可见损伤及泄漏 | |||||||
7 | Surge Voltage Test 浪涌电压 | After surge voltage applied at a cycling rate of 30 seconds charge and 5.5 minutes discharge 1000 successive test cycle. 加1.15倍额定电压充电30秒后放电5分30秒，连续循环1000次后测量。 | Capacitance Change 容量变化 | Within±15% of the initial value 初始值的±15%以内 | ||||
TANδ 损耗角正切 | Within specified value 不大于规定值 | |||||||
Leakage Current 漏电流 | Within specified value 不大于规定值 | |||||||
Physical外观 | No broken and undamaged 无可见损伤及泄漏 | |||||||
8 | Solderability Test 可焊性 | After the lead wire fully immersed in the solder for 2±0.1secs at a temperature of 235±2℃,the solder coating must be more than 95% 引线浸入235±2℃的焊料中，持续 2±0.1秒，拔出后引线表面被焊料覆盖的面积不少于浸入面积的95%。 | ||||||
9 | Mechanical Characteristics Test 引出端的强度 | 1.The test is about lead tabs strength. 1.本测试主要测试引出端的强度. 2.Tension Test: The lead tabs shall not be broken or any malformed condition after fixing capacitor vertically and pressing the following weight on the lead tabs of capacitor for 10±1 secs. 2.拉力测试：垂直固定电容器后，在引出端施加以下重量10±1秒钟，引出端不允许出现任何损伤和变形。 | ||||||
Lead tabs diameter 引出端直径(mm) | Weight重量(Kg) | |||||||
0.5 | 0.5 | |||||||
0.6、0.8 | 0.8 | |||||||
3.Bending Test: The capacitor is held in vertical position. Attach a weight to the lead tabs, slowly rotate the capacitor 90℃ to a same way in the opposite direction. Repeat it again(5secs per cycle). The lead tabs shall not be broken or cracked. 3.弯曲测试:竖直放置电容器，在其引出端悬挂下表重量的重物，转动电容器90度，恢复后，向相反方向转动90度，再恢复为一个周期，重复1次(每个循环5秒钟)。引线不会损伤破损。 | ||||||||
Lead tabs diameter 引出端直径(mm) | Weight重量(Kg) | |||||||
0.5 | 0.5 | |||||||
0.6、0.8 | 0.8 | |||||||
10 | Standards 引用标准 | Satisfies Characteristic of GB2693，IEC383、IEC384 | ||||||
11.Diagram of Dimensions尺寸图:
(mm)
D | ±0.5 | ±1.0 | ||||||||||||||||||
5 | 6or6.3 | 8 | 10 | 13 | 16 | 19 | ||||||||||||||
F±0.5 | 2.0 | 2.5 | 3.5 | 5.0 | 5.0 | 7.5 | 7.5 | |||||||||||||
L±2.0(max) | 11 | 11 | 12 | 13,16,20 | 20,25 | 25,31 | 35,40 | |||||||||||||
d±0.05 | 0.5 | 0.5 | 0.5or0.6 | 0.6 | 0.8 | |||||||||||||||
12. Case Size and Ripple Current尺寸和纹波电流
D×L(mm) wv mA μF | 6.3 ( 0J ) | 10 ( 1A ) | 16 ( 1C ) | 25 ( 1E ) | 35 ( 1V ) | 50 ( 1H ) | 63 ( 1J ) | |||||||
ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | |
0.1 ( 0R1) | 5×11 | 3 | ||||||||||||
0.22 ( R22) | 5×11 | 4 | ||||||||||||
0.33 ( R33) | 5×11 | 5 | ||||||||||||
0.47 ( R47) | 5×11 | 6 | ||||||||||||
1.0 ( 010) | 5×11 | 9 | ||||||||||||
2.2 ( 2R2) | 5×11 | 11 | ||||||||||||
3.3 ( 3R3) | 5×11 | 15 | ||||||||||||
4.7 ( 4R7) | 5×11 | 18 | 5×11 | 20 | ||||||||||
10 (100) | 5×11 | 20 | 5×11 | 25 | 5×11 | 25 | 5×11 | 25 | 5×11 | 30 | ||||
22 (220) | 5×11 | 30 | 5×11 | 35 | 5×11 | 35 | 5×11 | 40 | 6.3×11 | 50 | ||||
33 (330) | 5×11 | 40 | 5×11 | 40 | 5×11 | 50 | 6.3×11 | 60 | 8×12 | 60 | ||||
47 (470) | 5×11 | 45 | 5×11 | 50 | 5×11 | 50 | 6.3×11 | 65 | 6.3×11 | 73 | 8×12 | 90 | ||
100 (101) | 5×11 | 60 | 5×11 | 80 | 6.3×11 | 80 | 6.3×11 | 90 | 8×12 | 110 | 8×12 | 120 | 10×12 | 150 |
220 (221) | 6.3×11 | 100 | 6.3×11 | 110 | 8×12 | 140 | 8×12 | 150 | 10×13 | 190 | 10×16 | 240 | 10×20 | 270 |
330 (331) | 8×12 | 120 | 8×12 | 160 | 13×21 | 302 | 10×13 | 220 | 10×16 | 260 | 10×20 | 320 | 13×20 | 380 |
470 (471) | 8×12 | 170 | 8×12 | 190 | 10×13 | 250 | 10×16 | 290 | 10×20 | 350 | 13×20 | 430 | 13×25 | 500 |
1000 (102) | 10×13 | 300 | 10×16 | 360 | 10×20 | 440 | 13×20 | 540 | 13×25 | 620 | 16×25 | 790 | 16×31 | 900 |
2200 (222) | 13×20 | 580 | 13×20 | 620 | 13×25 | 700 | 13×21 | 725 | 16×31 | 1030 | 19×35 | 1230 | 19×40 | 1310 |
3300 (332) | 13×20 | 670 | 13×25 | 800 | 16×25 | 970 | 16×31 | 1120 | 19×35 | 1320 | 19×40 | 1400 | ||
4700 (472) | 16×25 | 1000 | 16×25 | 1050 | 16×31 | 1240 | 19×35 | 1440 | ||||||
6800 (682) | 16×25 | 1120 | 16×31 | 1300 | 19×35 | 1530 | 19×40 | 1630 | ||||||
10000 (103) | 19×35 | 1320 | 19×35 | 1620 | 19×40 | 1730 | ||||||||
D×L(mm) wv mA μF | 100 ( 2A ) | 160 ( 2C ) | 200 ( 2D ) | 250 ( 2E ) | 350 ( 2V ) | 400 ( 2G ) | 450 (2W) | |||||||
ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | ΦD×L | mA | |
0.47 ( R47) | 5×11 | 6 | 5×11 | 8 | 8×12 | 6 | 8×12 | 6 | ||||||
1.0 ( 010) | 5×11 | 9 | 5×11 | 12 | 8×12 | 9 | 8×12 | 9 | 8×12 | 12 | 10×16 | 15 | ||
2.2 ( 2R2) | 5×11 | 15 | 6.3×11 | 15 | 8×12 | 15 | 8×12 | 15 | 10×12 | 18 | 10×16 | 20 | 10×16 | 29 |
3.3 ( 3R3) | 5×11 | 18 | 8×12 | 20 | 8×12 | 20 | 10×13 | 20 | 10×16 | 23 | 10×16 10×20 | 25 | 10×20 | 35 |
4.7 ( 4R7) | 5×11 | 20 | 8×12 | 25 | 10×13 | 30 | 10×13 | 30 | 10×16 | 35 | 13×20 13×25 | 40 | 13×20 | 50 |
10 (100) | 6.3×11 | 35 | 10×13 | 40 | 10×16 | 45 | 10×20 | 45 | 13×20 | 50 | 13×25 16×25 | 70 | 13×25 | 75 |
22 (220) | 8×12 | 65 | 10×20 | 70 | 10×20 | 70 | 13×25 | 80 | 13×25 | 80 | 16×31 | 110 | 16×31 | 110 |
33 (330) | 10×13 | 95 | 13×20 | 110 | 13×25 | 110 | 13×25 | 100 | 16×32 | 140 | 16×21 | 131 | 19×35 | 150 |
47 (470) | 10×16 | 120 | 13×25 | 140 | 13×25 | 140 | 16×25 | 140 | 18×36 | 360 | ||||
100 (101) | 13×20 | 220 | 16×25 | 240 | 16×31 | 250 | 19×35 | 260 | ||||||
220 (221) | 16×25 | 420 | 19×35 | 430 | ||||||||||
330 (331) | 16×31 | 510 | ||||||||||||
470 (471) | 19×35 | 680 | ||||||||||||
1000 (102) | 19×40 | 1230 | ||||||||||||
I～額定紋波電流Rated ripple current：(mA，105℃，120Hz)
A． Marking：
Capacitor shall be marked with Capacitance, Rated Working Voltage, Max Operating Temperature and Polarity. All marking shall be legible and permanent.
B． Remark：
Customers’ specification will be accorded on request.
圆柱形、金属外壳、单向引出、引出方式为螺栓型式,有极性、有压力释放装置(采用点动防燃装置，当电容器内压增加或产品发生击穿时不会有易燃品飞出)。采用卡环固定安装，不适用于直接安装在线路板上。
莞荣誉電子有限公司 是一家集研發、生產、銷售及服務為一體的、高科技電容器生產企業，專項致力於為客戶提供專業的電容器產品解決方案，產品廣泛應用於LED顯示幕系統集成、汽車電子,安防領域.消費電子,通信設備.工業控制,等行業.荣誉電子專注於電容器相關領域，目前所經營的業務主要有鋁電解電容.薄膜電容.陶瓷電容.X級電容器的加工製造開發與生產等。公司自成立以來，在全體員工的共同努力下，產品及服務已逐步銷售到了國內各級市場並逐步出口到了歐、美、中東及港澳臺等海外的多個國家及地區，且以較高的性價比贏得了用戶的好評與認可。
公司擁有一支專業、且富有多年行業工作經驗的產品開發、設計團隊及一批高素質、職業化的管理精英，從而能在快速回應客戶需求、提供差異化產品設計、端到端的系統服務、助力客戶商業成功等方面得到了X的保證。
為了滿足市場及生產的需要，公司近萬平方米的標準化生產廠房，全面配備了組立封裝、SMT焊接、組裝測試、總裝老化等50條自動化程度較高的生產作業流水線。系統化、標準化、精細化管理體系的導入，讓我們在大規模生產的同時，既使產品的品質、性能等得到了充分的保證，又X地提高了效益、使製造成本得到了X的控制，從而總能使我們走在產品製造的X前沿，為客戶提供性價比較高的產品及服務。
電容器作為一種主要元器件，其節能、環保、壽命長等優異的特性早已得到世人的一致認可。有幸成為電容器行業的一員，在經營的道路上，我們必將發揮團隊的協作能力，以“誠信”為本，視“品質”為生命，以“客戶利益X大化”為經營目標，精益求精，全力打造X具性價比競爭優勢的生產製造基地，創電容器世界X品牌。
联系人：杨永林 业务
电 话：86 - 0769 – 85359259 手机号13427820351
传 真：86 - 0769 - 85359269
QQ：1484393065
地：中国广东东莞东莞市长安镇沙头工业区建安路640号
址邮 编：523873
公司lyyl@honordz.com 公司网址http://www.honorzd.com
